Just How to Replace a Bathtub
Just How to Replace a Bathtub
Blog Article
We have come across this article about Installing A Bathtub down the page on the web and thought it made sense to share it with you over here.
Setting up a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the task and also fit trying it. Instead of employing a professional to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you may need a professional plumber to make tube links.
This post will help you install a brand-new tub in your restroom if you have currently gotten a new tub and also don't require to transform the plan of your previous water supply pipelines.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of both wooden boards under its feet, place the tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and check all joints and new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has been utilized at least once as this will certainly resolve it right into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final position.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I discovered that piece about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Sharing is good. Helping others is fun. Thanks a lot for your time invested reading it.
More Details Report this page